There are some trips to the range that I remember very clearly…
A decade or so ago, I bought an H&K USPc. I immediately took it to the range, had the sights swapped out, and took it onto the range for a test fire.
The darn thing shot low. I took it back to the gunsmith and told him he’d screwed up the sights and asked him to fix it.
After a few tries of convincing me that the problem was me and not the gun, he asked one of the other guys (who happened to be one of the guys who later founded Silencerco and Dead Air) to go out onto the range with me and he proceeded to shoot out the bullseye with his first few rounds.
Pappas turned and looked over his shoulder at me and said, “The sights are fine…it’s your trigger finger that’s the problem.”
I learned a big lesson that day and I’ve seen this play out hundreds of times in the years since.
It’s incredibly common and natural for shooters claim that a gun is shooting off to the right, off to the left, or low but it’s usually not a hardware problem…it’s a software problem that can be fixed without tools.
What’s worse is that shooters adjust their aim to try to fix the problem.
A typical example is for a shooter to consistently be shooting off the mark because they’re consistently making the same mistake. Let’s say that they’re hitting low.
Their solution is to adjust their aim high so that they’re hitting the bullseye for a few rounds.
But then they correct their mistake and start shooting high!
So, instead of figuring out and fixing the problem, they just chase their misses around the target or use terms like “combat accurate” to cover up the real problem. Not fun. Not necessary. And the result is training scars.
(To be clear, combat accurate groups are GREAT—for combat. They’re not great for slow fire, stationary, low stress shooting with full lighting. And if you want to be able to make combat accurate groups in a dynamic, chaotic, high stress situation, you need to be able to shoot tight groups in sterile conditions.)
What about “too much finger” or “too little finger?”
These corrections refer to pressing the trigger with your trigger finger making contact with the trigger too close to the knuckle or too close to the tip of the finger.
On a single action target pistol with a light trigger or rifle that’s sized for the shooter, these are completely valid corrections.
On a defensive pistol, things get real blurry, real quick.
The “correct” trigger finger position is the one that will let you press a trigger straight to the rear without disturbing sight alignment.
Unfortunately, it may change from gun to gun (because of grip size and angles) and it may change from shooter to shooter.
If you’ve got a technically “correct” trigger finger position on a double stack .45, it may cause you to push all of your shots to the left when you’re using a single stack .380.
(simply do a few dry fire reps until you find the grip and finger position that will let you press the trigger without disturbing the sights and you’ll be good to go)
Your finger position on the trigger may need to change due to the weight of the trigger, length of the trigger press, or human factors like hand/finger size, arthritis, or how fatigued your finger is.
But regardless of where or how your finger hits the trigger, the one constant is that it should press the trigger straight to the rear without disturbing sight alignment.
The trick with errors like these is to identify and fix them quickly before they become a bad habit that’s harder and harder to fix.
That’s easy to do if you happen to be at the range getting a private lesson from a qualified instructor.
It’s quite a bit more difficult if you’re on your own or shooting with someone who’s a good shooter but doesn’t really know why they’re a good shooter.
That’s why I created the Brain Based Diagnostic Pistol Targets and had them printed on high visibility splatter paper.
I like to think of them as “cheat sheets” so you don’t have to remember everything you’ve ever heard or read about shooting just to quickly fix problems when you’re on the range. They don’t replace live instruction from a qualified instructor, but when that’s not immediately available, these are.
Simply set up the adhesive splatter target at 6-10 feet away, shoot a few rounds, see what pattern you’re making, look at the diagnostic chart that comes with them, make the correction that it says, and shoot another, tighter group! (some problems, like horizontal stringing, have multiple possible causes and you may have to try a couple before you find the one that brings you into the bullseye.)
We released these about a month ago. We had half dedicated to being sold alone and half dedicated to different training packages. The standalone targets sold out in 4 ½ hours and the backorders started piling up.
I immediately reordered 4x as many and was told that I’d get them by the 15th. About half of them finally got here Wednesday. 🙁
The good news is that we’re caught up on all of the backorders, have inventory, and you can order yours today!
The chances of getting the splatter targets before Christmas on Monday are pretty much zero, but you will get the print-at-home version of the targets and the diagnostic chart immediately and the splatter targets in the next 7-10 days, depending on where you live and weather.
Right now, the print-at-home targets are available in both right and left handed versions, but the splatter targets are right handed only. You can still use them as a lefty…you just have to flip them in your head.
by Mike Ox
Mike Ox is an avid defensive and competitive shooter who has co-created several firearms training products, including Dry Fire Training Cards, https://se965.infusionsoft.com/go/dftcmedia/loadout
Dry Fire Fit, 21 Day Alpha Shooter, and See Faster, Shoot Faster. His brain based training focuses on accelerated learning techniques for shooting as well as controlling brain state and brain chemistry for optimal performance in extreme stress situations. Learn more about dynamic dry fire training for defense and competition at www.DryFireTrainingCards.com/blog
Featured Photo courtesy of Heath Layman
If you enjoyed this article, please consider supporting our Veteran Editorial by becoming a SOFREP subscriber. Click here to get 3 months of full ad-free access for only $1